Copyright 2012 by ELBOX COMPUTER

Spider USB EHCI and OHCI drivers for the Poseidon stack
spider.device ver.3.22

-----
Licence

By using this software, you are agreeing to be bound by the terms 
and conditions of the Licence Agreement (Licence.txt).

-----
Registration

To register Spider USB drivers (spider.device), send an e-mail to 
support@elbox.com with "subscribe Spider drivers" in the subject. 
In the body, give the Spider serial number (see the Spider board 
and Spider box), your full name, e-mail address and 
where you have purchased the Spider II USB 2.0 Hi-Speed card.

-----
Requirements

- One free PCI slot
- Mediator Multimedia CD (for Mediator based systems)
- active Voodoo or Radeon gfx card in any Mediator PCI slot
- Poseidon stack (for Amithlon and Mediator based systems)
- Windows 2000 or Windows XP (for PC systems)
- Mac X OS (for Mac systems)

-----
Hardware Installation (in Amiga)

Fit Spider II USB 2.0 PCI card in any Mediator PCI slot marked 
with the number higher than the PCI slot in which the Voodoo 
graphic card is installed. In the Mediator PCI 1200 we 
recommend using Spider in the lowest, 4th PCI slot.

-----
Hardware Installation (in PC and Mac)

Fit Spider II USB 2.0 PCI card in any PCI slot.

-----
Software Installation

Install the Poseidon stack package. The current version is 
available at <http://www.platon42.de/poseidon.html> website.

Copy enclosed spider.device to Devs:USBHardware drawer.

Open Trident and go offline.
Open SHELL window and write:
AddUSBHardware Devs:USBHardware/spider.device 2
AddUSBHardware Devs:USBHardware/spider.device 0
AddUSBHardware Devs:USBHardware/spider.device 1
Go back to Trident and save your config.

Note: Spider.device ver.3.22 requires:
      the Poseidon stack ver.4.4 or higher,
      pci.library ver.9.0 or higher (Mediator users only),
      powerpci.library ver.2.11 or higher (Amithlon users only). 

-----
Spider ports

Spider USB 2.0 Hi-Speed PCI card is equipped with 5 USB ports.
These ports are controled by three independent USB controllers:
one EHCI (USB 2.0) and two OHCI (USB 1.1).

5 ports of EHCI controller are supported by spider.device at UNIT 2,
3 ports of OHCI 0 controller are supported by spider.device at UNIT 0,
2 ports of OCHI 1 controller are supported by spider.device at UNIT 1.

At the computer start all Spider ports are connected to the Spider 
EHCI Hi-Speed controller. When Spider detects an USB 1.1-standard
device connected to the Spider port, this port is switching to the
appropriate Spider OHCI controller.


EHCI ports    OHCI ports  -
                           |-----  
unit2 port1   unit0 port1  |O    |               EHCIport    OHCI port
                           |      -------------
unit2 port2   unit1 port1  |O                O |unit2 port5 unit0 port3
                           |                   |
unit2 port3   unit0 port2  |O                  |
                           |                   |
unit2 port4   unit1 port2  |O                  |
                           |                   |
                           |  ----             |
                           |--    -------- ----      
                           |
                           |

Note: In the spider.device ver. 3.10 the lower Spider port (unit2 
      port 4 / unit1 port2) is set as the OHCI port independently 
      of the type of the connected USB device. If you have any device 
      which does not work correctly in USB 2.0 (EHCI) mode use it in
      this port.  


Note: If you use external Hi-Speed USB 2.0 HUB do not connect any
      USB 1.1 devices to it. Full-Speed and Low-Speed devices should 
      be connected directly to the Spider card or via USB 1.1 HUB. 
      

------
DriveSpeed

DriveSpeed is used for checking speed of any USB drives.

Syntax:
DriveSpeed usbscsi.device n
where n is the unit number.


Support Department of ELBOX COMPUTER, Inc.
mailto: support@elbox.com  http://www.elbox.com
